Samsung Washing Machine Error Code: New Vs Old Error Code

Posted on
Samsung Washing Machine Error Code – How to fix error in Samsung washing machine. For convenience, arranged in a convenient and understandable table below. As additional information, this article also presents how to repair a Samsung washer code 4C (4E), 1E etc
The Samsung firm has a wide range of washing machine models. Despite the fact that their error codes are generally standardized, the error indicators vary greatly.
In current washing machines with displays, it’s as simple as displaying an alphanumeric problem code.
samsung washing machine error code

 

Even yet, previous models’ display designs contained patterns of burning and flashing LEDs (indicators). We’ll try to cover the most of them in this page, including those found in older models.

What does the error code means and how to fix it?

Please use the table below to find the error code that is appearing on your Samsung washing machine and the solution needed to resolve the issue.

Samsung Dryer Error Codes What To Check How To Clear

 

New Code Old Code Cause Solution
1E E7 Water level sensor Issue
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new program.
If problem persists please call the customer support team.
3E
3E1
3E2
3E3
3E4
EA
EB
Motor defect
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new program.
If problem persists please call the customer support team.
EA E1 Water supply error. The appliance is not detecting that the unit is filling with water
Check water supply is turned on and that there is adequate water pressure (min:0.5bar, max: 8bar).
Check to see if the water hoses are not kinked. Check Inlet filters inside end of Water Valve.
If water supply is OK, please call the customer support team.
4E1
4E2
4Ed Water temperature issue
Check water hose is connected to a cold supply and not a hot supply. Cold water is usually indicated by a blue tap.
If problem persists please call the customer support team.
5E
E2 Water drainage issue. Water is not draining from appliance.
Water drainage issue. Water is not draining from appliance.
Check drainage pump filter for blockages (e.g. lint, coins hair, clips)
Check drain hose and waste connection for kinks and blockages.
Then select a spin cycle to drain the remaining water in the appliance.
If problem persists please call the customer support team.
6E Water heater not functioning Please call the customer support team.
6F Unknown: this is not an error code. Contact us about this. Please call the customer support team.
8E Over current error
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new program.
If problem persists please call the customer support team.
9E1
PH1 Power error
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new program.
If problem persists please call the customer support team.
9E2 Plo Power error
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.
If problem persists please call the customer support team.
AE 13E Signal communication error between Main PCB and Sub PCB
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new program.
If problem persists please call the customer support team.
bE Motor issue
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new program.
If problem persists please call the customer support team.
bE1 12E Power button issue
Button held in too long. Check whether any of the buttons are sticking or are stuck in. Disconnect appliance from mains and clean the buttons with a lightly dampened cloth.
If problem persists please call the customer support team.
B2/bE2 14E Control button issue
Button held in too long. Check whether any of the buttons are sticking or are stuck in. Disconnect appliance from mains and clean the buttons with a lightly dampened cloth.
If problem persists please call the customer support team.
bE3 18E Button defective Please call the customer support team.
CE E8 Water cool down issue Check water hose is connected to a cold supply and not a hot supply. Cold water is usually indicated by a blue tap.
dE
dE1
Ed Door issue
Check that the door is closed fully.
Check nothing is trapping in the door.
Check unit is not overloaded.
If problem persists please call the customer support team.
dE2 On/Off switch error Button is being operated continuously. Please disconnect appliance from mains wait 5 minutes and then try again.
FE FE Fan error please call the customer support team
H1 HE Water temperature issue please call the customer support team
HE1 E5 Water heater not functioning please call the customer support team
HE2 HE2 Dryer heater not functioning please call the customer support team
HE3 Steam function does not operate normally please call the customer support team
HOT Appliance too hot This is not a fault; appliance fan will continue to run until the appliance is cool enough for the washing to be removed (55°C).
Then the door will unlock. – This prevents heater faults
LE
LE1
E9
11E
Natural drain/Water leak – Low water level detected during cycle.
Check that the level of the drain hose is not lower than the base of the washing machine. Additionally check for a water leak. If no trace of water, switch off the power, reconnect and try again.
OE
OF
E3 Overflow error Too much washing powder/liquid may have been added. Switch off the power to the appliance, wait 30 seconds then Switch the power supply back on. The drain pump should operate to drain the washing machine.
t1
ee2/t2
tSt
Appliance in test mode
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new program.
If problem persists please call the customer support team
SUD (sometimes misread as 5UD)
This occurs when too much foam is detected and is displayed whilst foaming is being removed.
This is not a fault.
The appliance will usually cure this fault on its own, however if it does not you will need to run either an “Eco drum clean” cycle (some models) or a 90°C cotton cycle with no detergent or washing load.
To prevent this from happening please reduce the quantity of detergent used.
tE EC Temperature sensor issue
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new program.
If problem persists please call the customer support team
tE1
tE2
tE3
Temperature sensor error
Please call the customer support team
UC Excessive fluctuation in the supply voltage
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.
If problem persists please call the customer support team
UE
E4 Unbalanced error – The load in the drum is unbalanced.
This is not a fault. The appliance is detecting an unbalanced load and is stopping the spin for safety reasons.
To help prevent this from occurring please redistribute washing by adding or removing items to ensure a more balance load.
Single large/heavy items such as bath mats or large towels are unlikely to spin on their own so please add 2/3 additional towels and put on another spin cycle.

Samsung Washer Code 4C (4E)

Samsung washer error code 4C (4E) error indicates that a problem with the water supply has been detected by the washing machine. A kinked or clogged water supply hose is the most prevalent cause of this problem.

To solve the problem, use the troubleshooting methods listed below.

#1 Inspect the water hose.

Low water pressure or a low flow rate on the mains water supply to the machine are the most common causes of water supply problems. This indicates that the water pouring into the machine is not strong enough.

The pressure of the water must be between 0.5 and 8 bar.

  1. Turn off the mains power to your washing machine.
  2. Move the machine forward to make room for the water hoses.
  3. Make that the water hose connecting to the machine is free of kinks and bends.

#2 Make sure the water supply is enough.

Make sure the washing machine’s water tap is fully operational.

#3 Clean the mesh filter on the water hose.

To avoid clogging, clean the water hose mesh filter at least twice a year.

#4 Make sure the dispenser drawer is clean.

If there is a blockage in the dispenser drawer, a 4C check code error message may be displayed. To clean the detergent drawer, follow the procedures in our step-by-step guide.

 

WF-S1054 Series Samsung Washing Machine Error Code

Samsung Washing Machine Error Code: New Vs Old Error Code

 

Error codes Description
HE1, HE2 The water in the tank does not heat up. Water overheats or heats slowly.
tE No signal from a temperature sensor
3E Tachogenerator does not transmit information
BE, IE Tachogenerator supplied the information about the wash
4E Too slow water enters a tank
LE Self-draining of water from the tank
CE The too high temperature when washing
OE Too much water in the tank
UE Unbalance of the laundry in the tub
5E Water drains too slowly or does not drain at all.
dE The hatch door is unlocked, the wash is interrupted
F15 Problems with heating the water in the tank to a predetermined temperature
F16 The door is not tightly closed
[/su_table]

 

R833GW1 Series Samsung Washing Machine Error Code

Description for Samsung washing machine error code for R833GW1 at list below

Error codes Description
E5, E6 The heating of water in the tank is incorrect.
EC The thermal sensor is faulty
EA No signal from tacho generator or signal too weak
EB, E7 Incorrect information from tacho sensor when washing
E1 Too slow water enters the tank
E3 Too much water in the tank
E9 Self-draining of water from the tank
E8 The too high temperature when washing
E4 Marked imbalance of laundry in the tank
E2 Problems with the discharge of wastewater from the tank
Door The hatch door is unlocked, the wash is interrupted

P1405J / P1205J / P1005J / P805J Series Samsung Washing Machine Error Code

Samsung Washing Machine Error Code: New Vs Old Error Code
Samsung error code 4c (4E)
Error codes Description
E1 Too slow water poured into the tank
E2 Problems with the discharge of wastewater from the tank
E3 Too much water in the tank
DOOR The hatch door is unlocked, the wash is interrupted
E4 Imbalance of linen in the tank
E5, E6 The heating of water in the tank is incorrect.
E7 Faulty water level sensor (pressure switch)
E8 The too high temperature when washing
E9 Self-draining of water from the tank

 

That’s the article about the error on the Samsung washing machine error code. You can start to repair by looking at the code that appears as well as Samsung error code 4c (4E), 1E etc.

Read also

I hope this article is useful