Toshiba Washing Machine Error Code List

• After starting draining in wash or spin process, the water level does not go down below the reset level even after the specified time has elapsed. (To be detected by the water level sensor) [7 mins 30 secs]
• Occurred by drain hose that was not put down or flattened hose, etc.

• Check around the drain hose (Forgot to put down t
  he hose, flattened hose, hose tip submerged in the water, a sleeve installed, extension of hose, etc.)
• Check the water level sensor and air tube.
• Check the drain valve operation.

#3 Toshiba Washing Machine Error Code E3

E3 : Laundry is unevenly distributed inside the washing bucket /Abnormal Unbalance

Unbalance occurred by uneven laundry load during the final spinning. (Unbalance detected t rectifying operation was repeated but the unbalance was not rectified.) (Abnormality alarm) When an unbalance was detected 3 times during the same spin process. In dry course, however, abnormality alarm sounds at the first abnormality detection

1. (E31): When abnormality was detected by the lid switch unbalance. (To be detected by the lid switch)
2. (E32): When abnormality alarm was detected by the vibration sensor. (To be detected by the rotation sensor.)

E5 Error Code Check Item And Description

• Is the tap not turned on? (When a bath water pump is used, this error may be displayed during rinsing.) >> Turn on the tap.
• Is dust or rubbish accumulated on the net of the water supply port? >> Clean the net of the water supply valve.
• Check the operation of the water supply valve.

#6 Toshiba Washing Machine Error Code E6

E6 : Washer motor, too much, low water level, clutch shaft, clutch shaft / Abnormal Motor Current

• Overcurrent flows through the motor while the motor is running (for all processes). (Current value flowing through the motor drive circuit is detected by the program timer assy.)
• Occurred by excessive laundry load, too low water level, defective wiring between the motor and the program timer assy, motor drive circuit failure, etc.
  1. (E61): While washing
  2. (E63): Abnormality occurred while spinning and there was no problem during washing.
  3. (E64): Occurred when spin only is set.
  4. (E65): When clutch is switched to washing.
  5. (E66): When clutch is switched to spinning

E6 Error Code Check Item And Description

• Laundry load exceeds the rated load. t Reduce the laundry amount.
• Water level is extremely too low than laundry load. t Make the set water level higher.
• It can be thought that the load on the pulsator became too large and the pulsator due to excessive laundry load thus became locked. This could be a cause of an overcurrent flowing in the motor.
• Check the operation of the motor.
• The followings are thought to be other factors (including occasional factors) of this error.
  (1) Current is not correctly switched to the motor due to defective wiring, etc.
  (2) The motor become locked due to the stuck or suspended clutch.
  (3) Current is not correctly switched to the motor due to influence of external noise, etc

#7 Toshiba Washing Machine Error Code E7

E7 : Washing motor jam, too much, low water level, clutch shaft, sanso clutch/ Abnormal Motor Rotation

• Abnormality occurred in the sensor signal which detects motor rotation while the motor is running (for all processes).
• Occurred by excessive laundry load, too low water level, defective wiring
  between motor and program timer assy, motor drive circuit failure, etc.
  1. (E71): While washing
  2. (E73): Abnormality occurred while spinning and there was no problem during washing.
  3. (E74): Occurred when spin only is set.
  4. (E75): When clutch is switched to washing.
  5. (E76): When clutch is switched to spinning.

E7 Error Code Check Item And Description

• Excessive voltage was added to the program timer assy by the motor while the motor is running (for all processes). (Voltage value applied to the motor drive circuit is detected by the program
  timer assy.)
• Occurred by excessive laundry load or motor program timer assy failure, etc.
  1. (E81): While washing
  2. (E83): Abnormality occurred while spinning and there was no problem during washing.
  3. (E84): Occurred when spin only is set.
  4. (E85): When clutch is switched to washing.
  5. (E86): When clutch is switched to spinning

E8 Error Code Check Item And Description

• Perform the same check as E6.
• It can be thought that the load on the pulsator became too large due to excessive laundry load and the pulsator thus became locked. This could be a cause of counter electromotive current generated from the motor.
• The followings are thought to be other factors (including occasional factors) of this error.
  (1) Program timer assy failure (detection circuit or microcomputer surrounding circuit failure)
  (2) Defective wiring inside the machine (disconnection or poor contact at the connector)

NOTE: The state where the circuit voltage becomes highest is when the lid is opened during spin top rotation. To perform reproduction for checking, carry it out at the abovementioned operation status

#9 Toshiba Washing Machine Error Code E9

E9 : Water leaks, the washing bucket is broken, the valve is stuck, entangled with the sensor of the broken water, do not forget to check the wires.