Zanussi washing machine error codes – Washing machines have become an indispensable household appliance. They simplify the laundry process and save time, energy, and money. However, like any other machine, washing machines can develop faults and malfunction. One common issue with Zanussi washing machines is the display of error codes, which can be frustrating for users. In this article, we will provide a comprehensive guide to troubleshooting Zanussi washing machine error codes.
Are you tired of being stumped by error codes on your Zanussi washing machine? Read on to learn how to troubleshoot and fix the problem!
Understanding Zanussi Washing Machine Error Codes
Zanussi washing machines come equipped with a display panel that shows error codes in case of a fault. Each error code is unique and signifies a specific issue. Understanding these codes is the first step towards troubleshooting the problem. Here are some common Zanussi washing machine error codes and what they mean:
E10 – Water Inlet Issue
The E10 error code on your Zanussi washing machine indicates a problem with the water inlet. This error code can appear if the machine is not receiving water or if the water pressure is too low. To troubleshoot this error code, you should check the water supply to the machine and ensure that the tap is turned on. You should also check the water inlet hose for any kinks or obstructions.
E20 – Drainage Issue
The E20 error code on your Zanussi washing machine indicates a drainage issue. This error code can appear if the machine is not draining water properly or if the drain hose is blocked. To troubleshoot this error code, you should check the drain hose for any blockages or kinks. You should also check the filter for any debris and clean it if necessary.
E30 – Door Lock Issue
The E30 error code on your Zanussi washing machine indicates a problem with the door lock. This error code can appear if the door is not closed properly or if the door lock is faulty. To troubleshoot this error code, you should ensure that the door is properly closed and try again. If the error code persists, you should check the door lock for any damage or wear and replace it if necessary.
E40 – Door Open Issue
The E40 error code on your Zanussi washing machine indicates that the door is open or not properly closed. This error code can appear if the door latch is faulty or if the door is not properly aligned. To troubleshoot this error code, you should ensure that the door is properly closed and try again. You should also check the door latch for any damage or wear and replace it if necessary.
If the washing machine does not operate normally, a alarm code will appear on the display. Please carry out the following checks.
| Error codes | Problem |
|---|---|
| E10 | Water intake overtime. Open the tap to check if the inlet hose is squashed or bent, check if the filter in the inlet valve is blocked or not; check that the water pressure is not too low. |
| E21 | Drain overtime. Check that the drain pump is blocked. |
| E30 | The door has not been closed. Check that the washing machine door is closed, check that clothes are not blocked by the door seal. |
| E50 | The voltage is too high. Check if the voltage is too high, if so, a constant voltage device is needed. |
Cleaning the pump
Depending on the level of soiling in the cycles and the frequency of the cycles, the filter should be checked and cleaned regularly.
The pump must be checked if:
- the machine does not empty and / or does not spin;
- the machine makes an unusual noise when emptying due to objects such as safety pins, coins, etc. blocking the pump.
Proceed as follows:
- disconnect the device;
- if necessary, wait until the water has cooled down.
- Open the pump door. Place a container near the pump to catch any spills.
- When the water stops flowing out, unscrew the pump cover and remove it. Always have a cloth nearby to dry any spilled water when removing the cover.
- Remove any objects from the pump impeller by turning it.
- Screw in the pump cover completely.
- Close the pump door.
There may be hot water in the appliance when the appliance is in use and depending on the program selected pump. Never delete pump cover during the wash cycle, always wait until the machine has finished the cycle and is empty. When putting on the cover, make sure it is tightened securely to prevent leakage and that small children can take it off.
Troubleshooting the Zanussi washing machine
Some problems arise from a lack of simple maintenance or omissions that can be easily resolved without calling an engineer. Before contacting your local Service Center, please perform the checks listed below.
| Malfunction | Possible cause / solution |
|---|---|
| The washing machine did not work. | Close the washing machine door. Press the Start / Pause key. |
| Water leak | Connect the water inlet pipe correctly. |
| Clothes spinning is not correct | Load and distribute the laundry evenly in the drum. |
| There is a specific smell in the washing machine | Run a self-cleaning cycle without clothes. |
| There is no water in the drum | There is no fault water under the visible area. |
| Water remains in the softener container | No fault – the softener’s performance is not affected. |
| Detergent residues remain on the clothes | The water-repellent component of the phosphorus-free detergent will remain on the clothes and form stains. Please select the «Rinse & Spin» program. or brush off the particles after the clothes are dry. |
| The washing machine does not fill | Unscrew the faucet. Check the selection of the procedure Reconnect the water inlet tube. Check if the water pressure is sufficient. Make sure the water inlet tube is not kinked or blocked. Close the washing machine door. |
| The washing machine fills and empties at the same time. | Make sure the end of the drain tube is higher than the water level inside the machine. Check that the drain pipe and waste water are sealed. |
| The washing machine is not draining | Check that drainage pumps are blocked. Make sure the drain pipe is not bent or blocked. Check the height of the drain nozzle, make sure it is 0.6-1 meter from the bottom of the washing machine. |
| Washing machine vibration | Level the washing machine. Attach the base. Make sure all delivery screws are removed. |
| The machine stops when the procedure is not finished | Power failure or water cut. |
| The drainage pump is noisy during operation after draining the water | The water inside the inner barrel has been drained, but there is still a small amount of water in the pump and drain tube. The drain pump is constantly running and taking in air, then you will hear a noise, which is normal. |
| The machine stops for a while during the washing procedure | The washing machine automatically adds water. There is too much foam in the wand, the foam is drained. |
