Midea Refrigerator Error Codes - Troubleshooting And User Manual

Midea refrigerator error codes – Midea refrigerators are known for their innovative features and reliable performance. However, like any other electronic appliance, they can occasionally encounter errors that require troubleshooting.

Understanding Midea refrigerator error codes and knowing how to resolve them can save you time and money. In this article, we will provide a detailed user manual that covers a wide range of error codes and their troubleshooting solutions.

Whether you’re a new Midea refrigerator owner or have been using one for years, this guide will help you navigate through any issues that may arise.

Table of Contents

Understanding Midea Refrigerator Error Codes

Midea refrigerators come equipped with an advanced error code system that helps diagnose and resolve issues efficiently. These error codes are displayed on the refrigerator’s control panel, providing valuable information about the nature of the problem. By understanding these error codes, you can take the necessary steps to troubleshoot and fix the underlying issue.

Troubleshooting Common Midea Refrigerator Error Codes

Midea Refrigerator Not Cooling

One of the most common issues faced by Midea refrigerator owners is the cooling problem. If your refrigerator is not cooling properly, it can lead to food spoilage and other inconveniences. To troubleshoot this issue, follow these steps:

Check the temperature settings: Ensure that the temperature settings are appropriate for your cooling needs. Adjust the settings if necessary.
Clean the condenser coils: Over time, dust and debris can accumulate on the condenser coils, affecting the refrigerator’s cooling performance. Clean the coils using a soft brush or vacuum cleaner.
Verify proper airflow: Ensure that there is adequate space around the refrigerator for proper airflow. Clear any obstructions that might hinder ventilation.
Check the door seal: A faulty door seal can cause cool air to escape, leading to inadequate cooling. Inspect the seal for any signs of damage or wear and replace if necessary.

Midea Fridge Error E1

The error code “E1” on your Midea refrigerator indicates a sensor fault. To resolve this issue, follow these steps:

Power off the refrigerator: Unplug the refrigerator from the power source.
Wait for a few minutes: Allow the refrigerator to remain unplugged for at least five minutes to reset the sensor.
Plug in and power on: Plug the refrigerator back in and power it on. The error code should disappear if the sensor fault was temporary.
Contact customer support: If the error persists, contact Midea customer support for further assistance or to schedule a service appointment.

Midea Refrigerator Error Code F1

The error code “F1” typically indicates a problem with the refrigerator’s defrost cycle. To troubleshoot this issue, follow these steps:

Check the defrost timer: Locate the defrost timer and ensure it is functioning correctly. If it is faulty, replace it.
Inspect the defrost heater: The defrost heater is responsible for melting frost and ice buildup on the evaporator coils. Check the heater for continuity using a multimeter. If it’s defective, replace it.
Examine the defrost thermostat: The defrost thermostat monitors the temperature of the evaporator coils. Test it for continuity and replace if necessary.
Verify the defrost control board: The defrost control board controls the timing and duration of the defrost cycle. If it malfunctions, replace it.

User Manual for Midea Refrigerator Error Codes

Midea Refrigerator Temperature Settings

The temperature settings on your Midea refrigerator play a crucial role in preserving food freshness and preventing spoilage. Follow these guidelines for optimal temperature settings:

Refrigerator compartment: Set the temperature between 35°F (1.7°C) and 38°F (3.3°C) to keep perishable items fresh.
Freezer compartment: Set the temperature between 0°F (-17.8°C) and 5°F (-15°C) to preserve frozen foods.

Midea Fridge Control Panel

The control panel of your Midea refrigerator provides easy access to various features and settings. Familiarize yourself with the control panel functions to make the most of your refrigerator:

Temperature controls: Adjust the temperature settings for the refrigerator and freezer compartments.
Mode selection: Switch between different modes such as Normal, Eco, Vacation, or Turbo, depending on your cooling requirements.
Alarm settings: Enable or disable audible alarms for open doors, temperature fluctuations, or power failures.

Midea Fridge Defrost Cycle

The defrost cycle is an essential function of your Midea refrigerator that prevents ice buildup on the evaporator coils. Understanding the defrost cycle helps maintain optimal cooling efficiency. Here’s how the defrost cycle works:

Detection: The refrigerator’s sensors detect frost buildup on the evaporator coils.
Initiation: The defrost timer activates the defrost cycle at regular intervals or when excessive frost is detected.
Heating: The defrost heater turns on and heats up the evaporator coils, melting the frost and ice.
Drainage: The melted water flows into a drain pan or down a drain tube, preventing water accumulation.
Cooling: Once the defrost cycle is complete, the refrigerator resumes normal cooling operations.

Midea refrigerator error codes And Description

Midea refrigerator error codes: Troubleshooting and how to fix

IMPORTANT: DO NOT try to repair your refrigerator yourself. Doing so invalidates the warranty.

#1 The refrigerator is not on or is not cooling

The refrigerator is unplugged >> Make sure that the refrigerator power cord is fully plugged into the electrical outlet.
The fuse on the circuit is blown or the circuit breaker is tripped >> Check the house fuse / circuit breaker box and replace the fuse or reset the circuit breaker.
Power failure >> If a power failure occurs, the refrigerator turns off. Wait until the power is restored.
Temperature control is not set to correct temperature. >> Adjust the temperature to a lower setting.
The clearance between the refrigerator and surrounding cabinets or wall is insufficient. >> Make sure there is adequate clearance around the refrigerator, and remove all items from the top of the refrigerator to maximize air circulation. See “Location Requirements.”

#2 The refrigerator door does not close completely

Food packages are interfering with the door. >> Move or remove some food items.
The door gaskets are dirty >> Clean the door gaskets.
The refrigerator may not be level. >> Level the refrigerator.

#3 The LED lights do not come on

The refrigerator is unplugged. >> Plug refrigerator into a grounded 3 prong outlet.
LED light is burned out. >> Contact a qualified technician to replace the burned out LED.

#4 Food in the refrigerator is not cold

The door has been opened too often or was not closed properly. >> Make sure that the door is closed properly.
A large amount of food was recently added. >> Allow time for the recently added food to cool, and then check again.
The door is not closed completely. >> Check the door gasket and food distribution, and make sure that the door closes completely.
The refrigerator has been disconnected for a period of time. >> Allow 4 hours for the refrigerator to cool completely before adding food.
The temperature control is set too warm. >> Set the temperature control to a colder setting.

#4 Items in the refrigerator compartment are freezing

The air vents are blocked. >> Place large items on the sides of the top shelf so that they are not blocking the air circulating from the vent in the center

#5 The refrigerator makes unusual noises or vibrations

The refrigerator may not be level. >> Adjust the leveling feet located on the front corners of the refrigerator until the refrigerator is level.
The refrigerator cabinet is touching a wall. >> Move the refrigerator away from the wall.
Metal parts undergo expansion and contraction. >> This is normal.
Refrigerant is circulating throughout the system. >> This is normal.

#6 Moisture is building up in the interior of the refrigerator

The door has been opened too often or was not closed properly. >> Make sure that the door is closed properly.
The refrigerator is located in a humid area. >> Move the refrigerator to a drier location.
The weather is hot and humid. >> This is normal.

#7 The ice maker is not producing ice or is not producing enough ice

The refrigerator is not connected to a water supply or the water supply shutoff valve is not turned on. >> Connect refrigerator to water supply and turn water shutoff valve fully open.
The ice maker(s) are turned off. >> Turn on the ice maker(s). See “Controls.”
The refrigerator has just been installed. >> Wait 12 hours after ice maker installation for ice production to begin.
The ice storage bin is not in place. >> Make sure the ice storage bin is correctly installed.
A large amount of ice was recently removed. >> Allow sufficient time for ice maker to produce more ice.
An ice cube is jammed in the ice maker ejector arm. >> Remove ice from the ejector arm with a plastic utensil.

#8 The ice cubes are hollow or small NOTE: This is an indication of low water pressure.

The water shutoff valve is not fully open. >> Turn the water shutoff valve fully open.
There is a kink in the water source line. >> A kink in the line can reduce water flow. Straighten the water source line.
A water filter is installed on the refrigerator. >> Remove the water filter and operate the ice maker. If ice volume improves, then the filter may be clogged or incorrectly installed. Replace filter or reinstall it correctly.

#9 The water and ice dispenser do not operate properly

The refrigerator is not connected to a water supply or the water supply shutoff valve is not turned on. >> Connect the refrigerator to the water supply and turn the water shutoff valve fully open.
There is a kink in the water source line. >> A kink in the line can reduce water flow. Straighten the water source line.
Inadequate water pressure to the house. >> The water pressure to the house determines the flow from the dispenser. See “Water Supply Requirements.”
A refrigerator door is not closed completely. >> Make sure both doors to the refrigerator compartment are completely closed.
The water filter or bypass plug is not installed properly. >> Water cannot be dispensed without a water filter or the bypass plug correctly installed. See “Water Filter.”
Ice is blocking the ice delivery chute. >> Remove the ice bin from the upper ice compartment. Check the delivery chute and remove jammed ice using a plastic utensil, if necessary. Clean the ice delivery chute and the ice bin using a warm, damp cloth, and then dry both thoroughly. To avoid ice jams and to maintain a fresh supply of ice, empty the ice bin and clean both the bin and delivery chute regularly.
Ice bin is not properly seated in the ice maker compartment. >> Check the position of the ice bin.

#10 Water is leaking or dripping from the dispenser system NOTE: A few drops of water after dispensing is normal.

The glass was not held under the dispenser long enough. >> Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser pad.
The water filter was recently installed or replaced. >> Flushing the water system removes the air from the lines which causes the water dispenser to drip. Flush the water system. See “Flush the Water System.”

#11 The water from the dispenser tastes bad

Water has not been dispensed recently (approx. 4 days). >> Dispense and discard at least 1 gallon of water.
The water filter needs to be replaced. >> Replace the water filter when indicated.

#12 Water from the dispenser is warm

The refrigerator has just been installed. >> Allow 24 hours after installation for the water supply to cool completely.
The refrigerator is not connected to a cold water pipe. >> Make sure the refrigerator is connected to a cold water pipe.
A large amount of water was recently dispensed. >> Allow 3 hours for the water supply to cool completely.
Water has not been recently dispensed. >> The first glass of water may not be cool. Discard the first glass of water dispensed.

#13 Water is leaking from the back of the refrigerator

The water line connections were not fully tightened. >> See “Connect to Water.”

#14 Water is leaking from the pan under the freezer drawer

The refrigerator is automatically defrosting more frequently. >>Empty the drip pan. Make sure the refrigerator is not overcrowded and that stored food with a high liquid content, such as soups, are tightly sealed.
The doors or drawers are not closed completely allowing warm air to enter. >> Make sure all doors and drawers are closed completely.

Download Midea Refrigrator User Manual

MODEL NUMBER MRS26D5AST: DOWNLOAD
MODEL NUMBER MRQ22D7AST: DOWNLOAD
MODEL NUMBER MD-RT339WEDMX02, MD-RT339WEDMX06 DOWMLOAD
MODEL: MDRF632FG SERIES DOWNLOAD
MODEL: MDRT489MTB46-MY DOWNLOAD
MODEL: MDRS723MY SERIES DOWNLOAD
MODEL: MDRT267MTB28 MDRT267MTB30 MDRT267MTB50 DOWNLOAD
WHS-507FWEW1 / WHS-507FWESS1 WHS-625FWEW1 / WHS-625FWESS1 WHS-772FWEW1 / WHS-772FWESS1 DOWNLOAD
MODEL NUMBER MRB19B7AWW MRB19B7AST DOWNLOAD

FAQs about Midea Refrigerator Error Codes

Q: Where can I find a list of Midea refrigerator error codes?

To access a comprehensive list of Midea refrigerator error codes, refer to the user manual provided with your refrigerator. The manual contains detailed information about each error code and its corresponding troubleshooting steps.

Q: What does the Midea fridge error code E2 indicate?

The error code “E2” on your Midea refrigerator typically indicates a communication problem between the control board and other components. It is advisable to contact Midea customer support to diagnose and resolve the issue.

Q: Why is the Midea refrigerator compressor not working?

If the compressor of your Midea refrigerator is not working, it can lead to inadequate

cooling and potential food spoilage. Several factors can contribute to a non-functioning compressor:

Power supply issues: Ensure that the refrigerator is properly plugged in and receiving adequate power. Check the circuit breaker or fuse box to ensure there are no electrical issues.
Thermostat problems: The thermostat regulates the temperature and controls the compressor. If it is faulty, the compressor may not receive the proper signals to start. Consider checking or replacing the thermostat.
Overheating: If the compressor overheats, it may automatically shut down to prevent damage. Clean the condenser coils and ensure proper airflow around the refrigerator. Remove any obstructions that may be blocking ventilation.
Mechanical issues: Internal mechanical problems within the compressor itself may cause it to malfunction. In such cases, it is best to contact Midea customer support for professional assistance.

Q: How often should I clean the condenser coils?

It is recommended to clean the condenser coils at least twice a year or more frequently if you have pets or live in a dusty environment. Clean coils ensure efficient cooling and prevent potential issues with the compressor.

Q: Can I reset the error codes on my Midea refrigerator?

While some error codes can be resolved by power cycling the refrigerator, it is generally advisable to address the underlying issue causing the error. Power cycling may clear temporary errors, but persistent problems should be properly diagnosed and resolved to prevent further issues.

Q: Are there any specific maintenance tasks I should perform for optimal refrigerator performance?

Yes, regular maintenance can help prolong the lifespan and performance of your Midea refrigerator. Here are a few essential tasks:

Cleaning: Regularly clean the interior and exterior of the refrigerator, including shelves, drawers, and seals.
Defrosting: If your refrigerator has a manual defrost feature, defrost it regularly to prevent ice buildup and ensure efficient cooling.
Check door seals: Inspect the door seals for any cracks or gaps. Damaged seals can lead to temperature fluctuations and reduced efficiency. Replace them if necessary.
Keep the refrigerator stocked: A well-stocked refrigerator helps maintain consistent temperatures. If your refrigerator is mostly empty, fill it with water containers to help maintain optimal cooling.
Regularly check and replace filters: If your refrigerator has water or air filters, follow the manufacturer’s recommendations for regular replacement to maintain optimal performance.

Midea refrigerator error codes: Conclusion

In conclusion, understanding Midea refrigerator error codes and troubleshooting techniques is essential for maintaining the optimal performance of your appliance. By familiarizing yourself with the error codes, following the provided user manual, and implementing the suggested troubleshooting steps, you can resolve common issues and prevent potential problems. Remember to perform regular maintenance tasks and seek professional assistance when needed to ensure the longevity of your Midea refrigerator.